$268.58 Buy It Now or Best Offer
free,30-Day Returns
Seller Store
() %,
Location: Ontario, California, United States
Ships to: US,
Item: 294788667350
Condition:New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is … Read moreabout the conditionNew: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller’s listing for full details. See all condition definitionsopens in a new window or tab
ECCPP:ECCPP
UPC:Does not apply
Manufacturer Part Number:EC83722401
Placement on Vehicle:Front, Outer, Inner, Lower, Left, Right
Universal Fitment:No
Manufacturer Warranty:1 Years
Features:Greasable
Items Included:Mounting Hardware
Performance Part:No
Type:Control Arm & Ball Joint Assembly
Interchange Part Number:513179F,K5342,ES3453,EV195,K80539,K80538,66-1250,66-1255
OE/OEM Part Number:anti sway bar car linkage,anti roll bar,stabilizer bar linkage
Superseded Part Number:car inner outer tie rod end replacement,rods ends
Cotter Pin Hole:Yes
Material:Alloy Steel
Mounting Style:Bolt-On
Finish:Coated
eBay 1.Fitting the Following vehicle: 2000-2005 Buick Century 2005-2009 Buick LaCrosse 1998-2004 Buick Regal 2000-2011 Chevrolet Impala 2000-2007 Chevrolet Monte Carlo 1999-2005 Chevrolet Venture 1998-2003 Pontiac Grand Prix 2.Package Includes: 2x Wheel Hub Bearing -513179F 2x Front Sway Bar End Link -K5342 2x Front Outer Tie Rod End -ES3453 2x Front Inner Tie Rod End -EV195 1x Front Lower Control Arm And Ball Joint — Driver Side -K80539 1x Front Lower Control Arm And Ball Joint — Passenger Side -K80538 1x CV Axle Shaft -66-1250 1x CV Axle Shaft -66-1255 3.Note Front Control Arm with Wheel Hub Bearing CV Axle Shaft For Impala Monte Venture 1.Fitting the Following vehicle: 2000-2005 Buick Century 2005-2009 Buick LaCrosse 1998-2004 Buick Regal 2000-2011 Chevrolet Impala 2000-2007 Chevrolet Monte Carlo 1999-2005 Chevrolet Venture 1998-2003 Pontiac Grand Prix 2.Package Includes: 2x Wheel Hub Bearing -513179F 2x Front Sway Bar End Link -K5342 2x Front Outer Tie Rod End -ES3453 2x Front Inner Tie Rod End -EV195 1x Front Lower Control Arm And Ball Joint — Driver Side -K80539 1x Front Lower Control Arm And Ball Joint — Passenger Side -K80538 1x CV Axle Shaft -66-1250 1x CV Axle Shaft -66-1255 3.Note (1).Please check the Compatible Fitment Chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Although some parts have grease fittings, other parts are factory sealed, but do not affect the fit and quality of the parts. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. 10 Year Warranty This item is backed by our 10-year warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only. Please note: Any modifications to an item of any kind before contacting us will void any and all warranty coverage for this item. Please contact us before modifying the part so that we have the opportunity to correct the situation. Suspension Control Arm Replacement Guideline: Control arms are installed in pairs on the front and rear axle and connect the chassis to the wheels as part of the suspension. Therefore, they have a significant influence on the driving characteristics of the vehicle. A dynamic or a comfortable driving style? The control arms are individually adjusted to the vehicle depending on the desired characteristics. They also absorb lateral movements and forces resulting from driving off and braking. Picture(A) A defective control arm can manifest in the following ways: (1).Noise (squeaking, creaking, rumbling). (2).Deteriorating driveability. (3).Increasingly woolly and imprecise steering. (4).Uneven tyre wear. Tip:If the control arm is in working order, it is possible to only replace the defective bearings and joints. However, replacing bearings, control arm bushings and ball joints can be very complex and costly. Picture(B) 1.First lift the vehicle using a car lift, ideally a wheel-free four-post car lift. This makes it easier to correctly tighten the control arm fixing screws. WARNING:Depending on the axle design, the control arm may need to be secured against falling with a suitable device, e.g. a transmission lifter. 2.Treat the fixing screws and nuts of the control arm with rust solvent and leave it to work for a few minutes so that they are easier to loosen. 3.On vehicles with automatic headlight levelling, it may be necessary to detach the leveling sensor from the control arm. Picture(C) 4.If the stabilizer is connected to the control arm, the next step is to loosen and remove the corresponding stabiliser fixing screws. 5.Loosen and remove the control arm fixing screws. 6.Loosen the ball joint at the steering knuckle with a suitable special tool (e.g. a puller). 7.Remove the old control arm. Picture(D) 8.Clean the mounting flange of the ball joint pin on the steering knuckle with sandpaper and then with brake cleaner. Otherwise single rust particles can enter the new control arm joint via the ball pin, potentially leading to premature failure of the joint. Picture(E) 9.Fit the new control arm with the supplied accessories and attach new fixing screws and nuts. Picture(F) 10.Reattach the stabilizer and, if applicable, the leveling sensor for headlight leveling to the control arm. NOTE:Do not tighten the fixing screws and nuts in this step, otherwise the rubber mounts will twist when the suspension compresses. This would lead to undesired preloading onf the mounts. Picture(G) 11.Now lower the vehicle until the suspension is compressed. Depending on vehicle type, load or unload the vehicle until the required height published in the specific installation instruction is reached. This is where a wheel-free four-post car lift is advantageous, as the underside of the vehicle can still be easily accessed once lowered. 12.Tighten the fixing screws with the torque stipulated by the vehicle manufacturer. 13.Lower the vehicle all the way. 14.Measure the chassis and adjust if necessary. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (2).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Frequently Asked Questions (1).How will I know that I have to renew my ball joint parts? Or replace them? If your ball joint fails, you will listen to a strange sound while driving. And that sound may help you to realize that your ball joint has failed and you have to renew them. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).Are worn ball joints dangerous? Yes, it can be quite dangerous. Because, a worn ball joint causes suspension damage, inspection failure, and breakage of related parts. It might make your front suspension come apart while driving, so the wheels move in whatever direction inertia takes them. That can lead to a fatal accident. (4).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (5).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. Item Specifics Brand ECCPP Manufacturer Part Number EC83722401 Placement on Vehicle Front Universal Fitment No Manufacturer Warranty 1 Years Features Greasable Items Included Mounting Hardware Performance Part No Type Control Arm & Ball Joint Assembly Interchange Part Number 513179F,K5342,ES3453,EV195,K80539,K80538,66-1250,66-1255 OE/OEM Part Number anti sway bar car linkage,anti roll bar,stabilizer bar linkage Superseded Part Number car inner outer tie rod end replacement,rods ends Cotter Pin Hole Yes Material Alloy Steel Mounting Style Bolt-On Finish Coated Item Specifics Brand ECCPP Manufacturer Part Number EC83722401 Placement on Vehicle Front Universal Fitment No Manufacturer Warranty 1 Years Features Greasable Items Included Mounting Hardware Performance Part No Type Control Arm & Ball Joint Assembly Interchange Part Number 513179F,K5342,ES3453,EV195,K80539,K80538,66-1250,66-1255 OE/OEM Part Number anti sway bar car linkage,anti roll bar,stabilizer bar linkage Superseded Part Number car inner outer tie rod end replacement,rods ends Cotter Pin Hole Yes Material Alloy Steel Mounting Style Bolt-On Finish Coated Discount Targeted Disounts Terms (1).Targeted Discount Terms only apply to auto parts purchased from ECCPPAUTOPARTS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. (3).Targeted Discount will be refunded from buyer’s payment, which means ECCPPAUTOPARTS won’t provide any extra targeted discounts if full refund is issued. Targeted Shipping Discount (4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items. Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).ECCPPAUTOPARTS has the final power of interpretation of all the above Targeted Discount Terms and Procedures. Shipping WARNING: Cancer and Reproductive Harm — www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Warranty Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to the auto parts purchased from ECCPPAUTOPARTS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).ECCPPAUTOPARTS carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).ECCPPAUTOPARTS promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise ECCPPAUTOPARTS has the right to refuse any replacement requests. (5).ECCPPAUTOPARTS promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise ECCPPAUTOPARTS has the right to refuse any replacement requests. (6).ECCPPAUTOPARTS carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).ECCPPAUTOPARTS has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. Return (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Best Sales Pair Manual Adjust Tow Mirrors For 1988-1998 Chevy GMC C K 1500/2500/3500 USD 57.09 ECCPP 2 Pcs Wheel Hub Bearing Front For Buick LaCrosse Century Regal Lesabre FWD USD 60.95 Universal 12V Low Pressure 5-9 PSI Electric Fuel Pump Installation Kit E8012S USD 13.99 Pair For 2007-2014 Chevy Silverado Sierra Towing Power Heated LED Signal Mirrors USD 119.58 Front Wheel Hub Bearing For Chevy Monte Carlo Impala Cadillac Eldorado DTS FWD USD 40.38 Newly Listed ECCPP Valve Cover Gasket For 07-13 BMW X5 Z4 X3 528xi 530i 528i xDrive 3.0L DOHC USD 13.71 For 2000-2006 Lincoln LS Window Regulators w/ Motor Rear Left & Right USD 78.95 Turbo Turbocharger For Mazda 3 2.0 2.3L 2007-2013 53047109904 USD 161.98 Universal Adjustable Gloss Black Front Bumper Lip Spoiler High Quality PP USD 42.29 ECCPP Head Gasket For 98-10 Chrylser Sebring Dodge Stratus 2.7L DOHC VIN R U T USD 29.49 Front Control Arm with Wheel Hub Bearing CV Axle Shaft For Impala Monte Venture 1.Fitting the Following vehicle: 2000-2005 Buick Century 2005-2009 Buick LaCrosse 1998-2004 Buick Regal 2000-2011 Chevrolet Impala 2000-2007 Chevrolet Monte Carlo 1999-2005 Chevrolet Venture 1998-2003 Pontiac Grand Prix 2.Package Includes: 2x Wheel Hub Bearing -513179F 2x Front Sway Bar End Link -K5342 2x Front Outer Tie Rod End -ES3453 2x Front Inner Tie Rod End -EV195 1x Front Lower Control Arm And Ball Joint — Driver Side -K80539 1x Front Lower Control Arm And Ball Joint — Passenger Side -K80538 1x CV Axle Shaft -66-1250 1x CV Axle Shaft -66-1255 3.Note (1).Please check the Compatible Fitment Chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Although some parts have grease fittings, other parts are factory sealed, but do not affect the fit and quality of the parts. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. 10 Year Warranty This item is backed by our 10-year warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only. Please note: Any modifications to an item of any kind before contacting us will void any and all warranty coverage for this item. Please contact us before modifying the part so that we have the opportunity to correct the situation. Suspension Control Arm Replacement Guideline: Control arms are installed in pairs on the front and rear axle and connect the chassis to the wheels as part of the suspension. Therefore, they have a significant influence on the driving characteristics of the vehicle. A dynamic or a comfortable driving style? The control arms are individually adjusted to the vehicle depending on the desired characteristics. They also absorb lateral movements and forces resulting from driving off and braking. Picture(A) A defective control arm can manifest in the following ways: (1).Noise (squeaking, creaking, rumbling). (2).Deteriorating driveability. (3).Increasingly woolly and imprecise steering. (4).Uneven tyre wear. Tip:If the control arm is in working order, it is possible to only replace the defective bearings and joints. However, replacing bearings, control arm bushings and ball joints can be very complex and costly. Picture(B) 1.First lift the vehicle using a car lift, ideally a wheel-free four-post car lift. This makes it easier to correctly tighten the control arm fixing screws. WARNING:Depending on the axle design, the control arm may need to be secured against falling with a suitable device, e.g. a transmission lifter. 2.Treat the fixing screws and nuts of the control arm with rust solvent and leave it to work for a few minutes so that they are easier to loosen. 3.On vehicles with automatic headlight levelling, it may be necessary to detach the leveling sensor from the control arm. Picture(C) 4.If the stabilizer is connected to the control arm, the next step is to loosen and remove the corresponding stabiliser fixing screws. 5.Loosen and remove the control arm fixing screws. 6.Loosen the ball joint at the steering knuckle with a suitable special tool (e.g. a puller). 7.Remove the old control arm. Picture(D) 8.Clean the mounting flange of the ball joint pin on the steering knuckle with sandpaper and then with brake cleaner. Otherwise single rust particles can enter the new control arm joint via the ball pin, potentially leading to premature failure of the joint. Picture(E) 9.Fit the new control arm with the supplied accessories and attach new fixing screws and nuts. Picture(F) 10.Reattach the stabilizer and, if applicable, the leveling sensor for headlight leveling to the control arm. NOTE:Do not tighten the fixing screws and nuts in this step, otherwise the rubber mounts will twist when the suspension compresses. This would lead to undesired preloading onf the mounts. Picture(G) 11.Now lower the vehicle until the suspension is compressed. Depending on vehicle type, load or unload the vehicle until the required height published in the specific installation instruction is reached. This is where a wheel-free four-post car lift is advantageous, as the underside of the vehicle can still be easily accessed once lowered. 12.Tighten the fixing screws with the torque stipulated by the vehicle manufacturer. 13.Lower the vehicle all the way. 14.Measure the chassis and adjust if necessary. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (2).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Frequently Asked Questions (1).How will I know that I have to renew my ball joint parts? Or replace them? If your ball joint fails, you will listen to a strange sound while driving. And that sound may help you to realize that your ball joint has failed and you have to renew them. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).Are worn ball joints dangerous? Yes, it can be quite dangerous. Because, a worn ball joint causes suspension damage, inspection failure, and breakage of related parts. It might make your front suspension come apart while driving, so the wheels move in whatever direction inertia takes them. That can lead to a fatal accident. (4).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (5).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. Item Specifics Brand : ECCPP Manufacturer Part Number : EC83722401 Placement on Vehicle : Front Universal Fitment : No Manufacturer Warranty : 1 Years Features : Greasable Items Included : Mounting Hardware Performance Part : No Type : Control Arm & Ball Joint Assembly Interchange Part Number : 513179F,K5342,ES3453,EV195,K80539,K80538,66-1250,66-1255 OE/OEM Part Number : anti sway bar car linkage,anti roll bar,stabilizer bar linkage Superseded Part Number : car inner outer tie rod end replacement,rods ends Cotter Pin Hole : Yes Material : Alloy Steel Mounting Style : Bolt-On Finish : Coated Item Specifics Brand ECCPP Manufacturer Part Number EC83722401 Placement on Vehicle Front Universal Fitment No Manufacturer Warranty 1 Years Features Greasable Items Included Mounting Hardware Performance Part No Type Control Arm & Ball Joint Assembly Interchange Part Number 513179F,K5342,ES3453,EV195,K80539,K80538,66-1250,66-1255 OE/OEM Part Number anti sway bar car linkage,anti roll bar,stabilizer bar linkage Superseded Part Number car inner outer tie rod end replacement,rods ends Cotter Pin Hole Yes Material Alloy Steel Mounting Style Bolt-On Finish Coated DiscountShippingWarrantyReturnFeedback Targeted Disounts Terms (1).Targeted Discount Terms only apply to auto parts purchased from ECCPPAUTOPARTS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. (3).Targeted Discount will be refunded from buyer’s payment, which means ECCPPAUTOPARTS won’t provide any extra targeted discounts if full refund is issued. Targeted Shipping Discount (4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items. Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).ECCPPAUTOPARTS has the final power of interpretation of all the above Targeted Discount Terms and Procedures. WARNING: Cancer and Reproductive Harm — www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to the auto parts purchased from ECCPPAUTOPARTS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).ECCPPAUTOPARTS carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).ECCPPAUTOPARTS promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise ECCPPAUTOPARTS has the right to refuse any replacement requests. (5).ECCPPAUTOPARTS promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise ECCPPAUTOPARTS has the right to refuse any replacement requests. (6).ECCPPAUTOPARTS carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).ECCPPAUTOPARTS has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Copyright of ECCPP. All rights reserved.
Frequently Asked Questions About Front Control Arm with Wheel Hub Bearing CV Axle Shaft For Impala Monte Venture in My Website
lalu.uz is the best online shopping platform where you can buy Front Control Arm with Wheel Hub Bearing CV Axle Shaft For Impala Monte Venture from renowned brand(s). lalu.uz delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.
What are the best-selling Front Control Arm with Wheel Hub Bearing CV Axle Shaft For Impala Monte Venture on lalu.uz?
lalu.uz helps you to shop online and delivers Arcteryx to your doorstep. The best-selling Arcteryx on lalu.uz are: Arc’teryx Womens Size 14 Gamma Lightweight Pants Light Gray Hiking Belted Mens Vintage Y2k ARCTERYX Soft Shell Jacket Outdoor Black Size L Mens New Arcteryx Delta Jacket Size Small Color Black Arc’teryx Vertex Alpine Gtx Sneakers Womens Sz 6.5 Running Shoes Gore Tex NWOB Arc’teryx Gamma LT Jacket Grey Men’s S Small Arcteryx Covert Hoody Pullover Men’s Women’s Unisex Green Polartec Fleece NEW! ARCTERYX Men Kyanite Hoodie Fleece Jacket—(XL)—Full Zip Fleece—“YUKON GOLD” ARCTERYX Gamma Utility 5” Shorts Black Nylon Hiking Climbing Women’s Sz 8 Arc’teryx Palisade Pants Mens 32×32 Black Climbing Trekking Performance Belted Arcteryx Pants Mens Extra Large Black Beta LT Waterproof Rain Hike Work 34×31 USMC GEN 2 Marpat Tan Woodland ILBE Main Pack w Lid Belt COMPLETE Arcteryx Arcteryx Atom lt Mens Jacket 24k Gold Limited Edition size XL Arcteryx Phase AR Zip Neck Mens XL Long Sleeve Quarter Zip Black Arcteryx Blade 28 Backpack Laptop Bag Carry-On Blue Travel — SAMPLE NWOT READ NWT NIP Arc’teryx Leaf Foliage Green 20th Anniversary Trucker Cap Hat One Size Arc’teryx Pullover Mens Medium Orange Gray Qtr Zip Polartec Caliber Sweatshirt Arcteryx Cerium LT Hoody Mens Green Puffer Jacket Down Size M Arc’teryx Gamma MX Hoody in Size M Men’s — Color Black — New w/Tags attached Arcteryx Polo Mens Medium Captive Performance Short Sleeve Hiking Arcteryx Konseal FL 9.5 Mens Arc’teryx Captive Long Sleeve Polo Shirt Mens Large Gray Hidden Snap Button Arc’teryx Creston Hiking Pants Mens 30 Black Waistband Relaxed Fit Straight Leg Arcteryx Nylon Hiking Backpack Nozone Arc’teryx Men’s Levon Pants Black Size 36 x 32 Stretch Cotton Blend Pre-owned NWT $100 Arc’teryx Rho LT Bottoms for Men Size Medium Color Forge arcteryx jacket Men’s XL atom LT Arcteryx Gamma LT Softshell Jacket Outdoors Gorpcore Men’s Size: Large Gray Arc’teryx Fortrez Hoody Mens Large Excellent Condition Arc’teryx Authorized Dealer Sign Vintage Streetwear TNF Arcteryx Style Outwear Oakley Softshell Jacket Men’s Arc’teryx LEAF Cold WX RHO Pants Crocodile — L Large Arcteryx Light Jacket Navy XXL Arcteryx Mantis 2 Waistpack Black Tan Shoulder Bag Crossbody From Japan NEW Arc’teryx Gamma MX Hoody in Size XL Men’s Color Blackbird — New w/Tags attached USMC MARPAT ILBE Arcteryx GEN 1 Lid (2-sided Molle) Very Good condition Arc’teryx_Therme Parka Men Arc’Teryx one size balaclava POLARTEC brand new ARCTERYX balaklava Arc’teryx Norvan Insulated Pants — Women’s Size 4 Regular Black NWT Mens Arc’teryx Edziza Kyanite Polartec Fleece Jacket Sweater sz L Arcteryx Alpha LT Beta Group Weiteng Brown Men’s Jacket Arcteryx Womens S Kyanite Black Hoody Full Zip Fleece Jacket *LOGO EMBROIDERED* Arc’teryx Gamma SL Anorak Mens XL Color Black Arcteryx Alpha SV Jacket (24k Black) (Size L) Arc’teryx Covert Cardigan 1/4 Zip Mens XL Color Black Made In Canada Arcteryx outdoor streetwear shirt men’s size M Arcteryx Fleece 1/4 Snap Henley Athletic Top S/M Small/Medium Dark Pink Arc’teryx XFunctional SV Pants — Rawhide — Size 34×35 — NWOT Arc’teryx Incendo Pant, Color Forage, Size XL Regular, NWT, ArcTeryx Fleece Jacket Womens Full Zip Black Polartec Sweater Hike Size XS Arc’teryx Mens XL Blue Strato Fleece Jacket ARCTERYX Gamma AR Jacket Arc’teryx Cita SL Hoodie — Women’s Arc’teryx Hoodie Land Rover Logo Size L Arc’teryx Mens Size 38×32 A2B Commuter Pant Dark Gray Reflective Pockets Arc’teryx Cranbrook Hat Black Size L-XL Arc’teryx Women’s Mota Long Coat Puffer Zip Up Nylon Hooded Black M ARC’TERYX GOTHIC HOODY ITALIAN WOOL JACKET XL UNISEX NEW ! Dark Gray RARE ! Arc’teryx Covert 1/2 Zip Mens Fleece Arcteryx Jacket Sz M Grey 34438 24093 ARCTERYX women’s AERIOS FL GTX hiking running shoes SASKAJAM/AEROSCENE size 7 Arc’Teryx Vintage Rt35 Red Black/Red Hiking Pack Size Large Vintage Arcteryx Hyllus Softshell Fleece Lined Hooded Jacket Mens Large ARC’TERYX Epsilon LT Jacket Womens Black Corporate Logo Arcteryx Mid Layer Arc’teryx Delta AR Pullover Mens Small Color Green NWT Arcteryx Women’s Rho LT Crew Base Layer Black Size : M ARCTERYX INSULATED JACKET WOMENS SIZE XL 34438 Arcteryx Oriel Leggings Womens L Gray Stash Pocket Yoga Outdoor Arc’teryx Cerium LT Hoody in Size L Men’s Color Black — New w/Tags attached Arc’teryx Gamma MX Hoody in Size XXL Men’s — Color Black — New w/Tags attached Arc’teryx Jacket Men’s Large Green Full Zip Fleece Polyester Polartec NWT Arcteryx Sentinel LT Gore-tex Jacket women’s Ski Snow SZ：S Arc’teryx Polartec Sweat Pants Womens Sz XS Elastic Waist Arcteryx Vest Men XL Black Full Zip Nylon Poly Sleeveless Zipper Pockets Stretch mens arcteryx Shorts. Size 38 Arcteryx Polo Shirt Mens Size Large Black Golfing Golf Outdooors Button Arc’teryx Aerios 30 Backpack 30 Liter Capacity Women’s Excellent Condition Blue Arcteryx Atom AR Hoody — Excellent — Mens XL — Bordeaux — 2022/2023 Updates ARCTERYX CERIUM LT Jacket MENS SIZE LARGE PUFFER DOWN arcteryx fission sv jacket black Insulated Men’s Large Vintage Arcteryx Bib Gore-Tex Xcr Black Pants Snowboarding Bib Snow Size Small Arc’teryx Atom LT Jacket Mens Medium Color Gray Great Condition Arc’teryx Atom LT Hoody Men’s Full Zip Jacket Size XL Arc’teryx Women’s Large Arenite Hoody Green Full Zip Fleece Lined Arc’teryx Atom Vest Black Arc’teryx SS21 ‘Micon GORE-TEX’ Shell Jacket Orange (2021) mens arcteryx Fleece Quarter Zip Large Green ARC’TERYX men’s large grey baselayer tights snow thermals NWD Arcteryx Vintage Rare Arc’teryx Strato Polartec Fleece Jacket Brown Olive Green Sz Large Arcteryx T Shirt Extra Large Blue Orange Arc’Word Logo Stretch Short Sleeve Arcteryx Jacket Womens XL Green Covert Hoody Full Zip Trim Fit Performance Arc’teryx Covert Pullover Hoody Men’s Small Orca Gray ARC’TERYX WOMEN’S COVERT CARDIGAN Jacket Sz L …in great condition…no… Arc’teryx Gamma Rock Pants Men’s Medium Feldspar (Gray) UEC Hiking, Climbing Arcteryx Aerios FL GTX Shoes 11 Mens Maroon GoreTex Hiking Running Trail Outdoor NWT Arc’teryx Leaf Crocodile Assault Balaclava FR Gen2 sz L/XL Unopened Arcteryx Gore-Tex Pro mens Orange Hooded Jacket size Large Arc’teryx — H150 Riggers Belt 7188 Medium? Preowned Arcteryx Puffer Jacket Womens Extra Small Darrah Mid Thigh Length Pockets Black Arc’teryx Palisade Pants Men’s 38×32 Belted Hiking Cargo Blue Arc’teryx Procline Hybrid Hoody Jacket Men’s Sz Large Blue Full Zip Arc’teryx Men’s 32×31 Slim Gray Lightweight Stretch Hiking Outdoor Pants Zipper Mens Pullover Fleece Hoodie